• My requests (0)
      You do not currently have any products added to your request.
      All requests
    Search
    All results
    Contact
    (636) 386-8022 Call now
    [email protected] Contact now
    Series
    B1.8320

    Electric Swing Clamps

    Parallel drive, position and clamping force monitoring, IO-Link connection optional, DC voltage 24 V, minimum energy demand
    Electric Swing Clamps
    Downloads
    Catalogue sheet
    USESFR
    Operating instructions
    Information Series
    Description
    B 1.8320 Electric Swing Clamps - Parallel drive

    IO-Link connection optional

    The electric swing clamp is driven by a wear-resistant brushless DC motor. The motor speed is transformed by means of a gear and a threaded spindle into the swing and stroke movement of the piston rod.
    For swinging the clamping arm by 180°, an axial stroke of only 3 mm is required.
    If the clamping arm collides during the swing motion with a workpiece, the mechanism is protected against overload.  
    The direct current motor is automatically and immediately switched off. When unclamping, the clamping arm always swings back to the off-position.

    Integrated control
    The electronic control for the DC motor is on a board in the housing of the electric swing clamp.

    Electric connection
    Power supply and signal exchange for external control are transmitted by two short cables with plug-type connector. Cable sockets are available for the customer's connection (see connection accessories). 

    Safe touch voltage
    The used DC voltage 24 V is considered to be a "low voltage" and thus it is not dangerous for people in case of contact.

    Power supply
    For motor and electronic control a DC voltage of 24 V with a residual ripple of max. 10 % is required.
    For the DC motor, we recommend the use of a switching power supply with a current output of 15 A per connected electric swing clamp. When operating several swing clamps at the same time, the line is to be enlarged correspondingly.
    The electronic control has to be supplied by a separate power supply (24 V DC / 100 mA).

    Advantages
     ● High clamping force
     ● Adjustable clamping force
     ● Clamping force monitoring
     ● Can be controlled individually or in common
     ● High operating safety by self-locking spindle drive
     ● Mechanical reclamping by Belleville springs
     ● Swing angle up to 180° available
     ● Overload protection device in the case of collisions with the clamping arm
     ● Electric position monitoring and extensive self-monitoring with diagnostic options
     ● Clamping stroke control possible
     ● Low voltage 24 V
     ● Leakage free
     ● Maintenance free (500,000 cycles).
     ● Code class IP 67

    Video
    Products (20)
    body design
    parallel drive (20)
    clamping arm seat
    cone 1:10 (20)
    swing stroke [mm]
    3 (20)
    total stroke [mm]
    26 (20)
    swing angle [°]
    swing direction
    position monitoring
    with (20)
    max. clamping force [kN]
    7.9 (20)
    metallic wiper
    code class
    IP 67 (20)
    nominal voltage [VDC]
    24 (20)
    camping force control
    with (20)
    axial pull force [kN]
    3 - 9 (20)
    usable clamping stroke [mm]
    20 (20)
    max. clamping time [s]
    3 (20)
    IO-Link
    Item no. CAD databody designposition monitoringmax. clamping force [kN]metallic wiper
    Item no.
    1835C000026P
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    Properties
    Item no.
    1835C000026P0I
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    Properties
    Item no.
    1835C000026PM
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    Properties
    Item no.
    1835C000026PMI
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    Properties
    Item no.
    1835C090L26P
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    Properties
    Item no.
    1835C090L26P0I
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    Properties
    Item no.
    1835C090L26PM
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    Properties
    Item no.
    1835C090L26PMI
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    Properties
    Item no.
    1835C090R26P
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    Properties
    Item no.
    1835C090R26P0I
    CAD data
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    Properties
    Item no.
    1835C000026P
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    swing angle [°]
    without
    swing direction
    none
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    without
    Item no.
    1835C000026P0I
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    swing angle [°]
    without
    swing direction
    none
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    with
    Item no.
    1835C000026PM
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    swing angle [°]
    without
    swing direction
    none
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    without
    Item no.
    1835C000026PMI
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    swing angle [°]
    without
    swing direction
    none
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    with
    Item no.
    1835C090L26P
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    swing angle [°]
    90
    swing direction
    ccw
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    without
    Item no.
    1835C090L26P0I
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    swing angle [°]
    90
    swing direction
    ccw
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    with
    Item no.
    1835C090L26PM
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    swing angle [°]
    90
    swing direction
    ccw
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    without
    Item no.
    1835C090L26PMI
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    with
    swing angle [°]
    90
    swing direction
    ccw
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    with
    Item no.
    1835C090R26P
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    swing angle [°]
    90
    swing direction
    cw
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    without
    Item no.
    1835C090R26P0I
    body design
    parallel drive
    position monitoring
    with
    max. clamping force [kN]
    7.9
    metallic wiper
    without
    swing angle [°]
    90
    swing direction
    cw
    swing stroke [mm]
    3
    total stroke [mm]
    26
    clamping arm seat
    cone 1:10
    code class
    IP 67
    nominal voltage [VDC]
    24
    camping force control
    with
    axial pull force [kN]
    3 - 9
    usable clamping stroke [mm]
    20
    max. clamping time [s]
    3
    IO-Link
    with
    Accessories (9)
    Item no. CAD data Description
    Item no.
    0341231
    CAD data
    Description
    Metallic wiper for 1835-XXX for piston rod Ø 36 mm as per data sheet B1.8310
    Item no.
    0354003
    CAD data
    Description
    Clamping arm, complete for 18X5-XXX with thread, material: 42CrMo4 max. 200 bar, as per data sheet B1.880
    Item no.
    3141991
    CAD data
    Description
    Cable socket Hirschmann CA3LD as per data sheet B1.8310
    Item no.
    3141992
    CAD data
    Description
    Cable socket Binder 423 12 POL. as per data sheet B1.8310
    Item no.
    3300325
    CAD data
    Description
    Dowel pin 6m 6x12 mm as per data sheet B1.8500
    Item no.
    3527015
    CAD data
    Description
    Nut M28 x 1.5 mm as per data sheet B1.880
    Item no.
    3548902A
    CAD data
    Description
    Clamping arm blank for 18X5-XXX high alloy steel1000....1200 N/mm2 as per data sheet B1.8310
    Item no.
    3823375L05000
    CAD data
    /
    Description
    Cable socket, 5 m cable 12 POL. as per data sheet B1.8310
    Item no.
    3921017
    CAD data
    Description
    Clamping arm, complete for 18X5-XXX without thread, material: 42CrMo4 max. 200 bar, as per data sheet B1.880
    Error loading CAD data. Please check your internet connection and try again.
    Please note: Our CAD data are generally simplified data and primarily reflect the outer contour and connections of the product (see also Terms of use). Please always refer to the relevant catalogue sheet for the exact dimensions with tolerances, in particular the information on mounting holes or attachments such as special clamps.